Presentation of the AVIDSEN 104257 Remote Control

Note: The remote control AVIDSEN 104257 is referenced with the following codes: 504250 or 104250.

The remote control AVIDSEN 104257 will simplify your life. Its durability and ease of use are remarkable. It is also programmable in record time: it requires no special equipment to perform its programming. Opening and closing your garage or gate has never been so simple.

Smartly Programmable with Self-Learning

Paired with an automation system, this remote control perfectly combines ease and productivity. The new remote control AVIDSEN 104257 can replace many older models. It will be delivered with its batteries and programming manual. The remote control AVIDSEN 104257 is a transmitter used for controlling garage door and gate automations. The programming of its white casing can be done through self-learning.

The remote control AVIDSEN 104257 is a functional and practical device thanks to its 4 silver-colored buttons, which will help you operate your garage door, your gate, and all your other automations simply and effectively. Its casing works with CR2032 batteries on a frequency of 433.92 MHz.

10 Controllable Devices

The remote control AVIDSEN 104257 is a reliable, efficient accessory that is fully suited for daily domestic use. It can control up to 10 devices thanks to its unique button combination. Its design has been revamped to give it a more modern and streamlined style. The remote control is white, its sides are equipped with a stainless steel frame, and its size allows for better handling. It features a keychain attachment to avoid misplacing it.

Eight Technical Specifications on the AVIDSEN 104257

1. First, this remote control has an AM modulation of type OOK. Its coding is of the Rolling code type at 16 bits (which equates to nearly 65536 possible combinations)
2. Next, it has a frequency of 433.92 MHz
3. Then, this transmitter is powered by approximately 3V per battery (of type CR2032)
4. Its radiated power is less than 10 mW
5. It has a battery life of 2 years, based on approximately 10 uses of 2 seconds per day on average.
6. Its operation is resistant to temperatures ranging from -20°C to +60°C
7. Its use is recommended indoors (in a sheltered place like the house, car, or garage) due to its protection index (IP40)
8. Finally, its dimensions are 20 x 40 x 70 mm

Compatibility of the AVIDSEN 104257 Remote Control

Before acquiring the remote control AVIDSEN 104257, it is wise to check that it is compatible with the following older models:

• AVIDSEN 104250
• the AVIDSEN 104250 BLACK device
• the AVIDSEN 104250 OLD2 product
• the AVIDSEN 104250 RED
• the AVIDSEN 104250 BRICO
• the AVIDSEN 104251 model
• the AVIDSEN 104350 system
• the AVIDSEN 654300 device
• the model AVIDSEN 654100
• the AVIDSEN 504713
• the AVIDSEN 614701
• the AVIDSEN 654100 model
• the AVIDSEN 654249
• the AVIDSEN 654250 transmitter
• the AVIDSEN 654300 remote control
• AVIDSEN 580408
• the AVIDSEN RMC-1LM 664700
• BLYSS 433MHZ
• ASTRELL 614701

It is also compatible with the following AVIDSEN gate motors:

• with the ANTHEA hydraulic swing gate motor
• STROMMA
• STYRKA
• KHÉA
• then with the ORANE 2 swing gate arm systems
• next with the OREA sliding gate automation models
• PSF

Programming the AVIDSEN 104257 Remote Control

Here are the instructions to help you program your transmitter:

• 1^st step: First, open the casing of your receiver, which is located near your motorization.
• 2^nd step: Next, on the receiver board, press and hold the programming button (RF) until the receiver’s LED (L1) turns off. Once the LED is off, release the programming button.
• 3^rd step: Then, within 10 seconds of the operation, press one of the buttons on your new remote control.
• 4^th step: Finally, hold this button until the receiver’s LED blinks, then release it.
• 5^th step: Then, wait 10 seconds.
• 6^th step: Congratulations! Your new remote control AVIDSEN 104257 is programmed and ready for use.

Programming from the Second Type of Installed Receiver:

• 1^st step: First, start by opening the casing of your receiver, which is located near your motorization.
• 2^nd step: Then, on the receiver board, press and hold the programming button (RX), then release the button until the receiver’s LED turns off. Wait 5 seconds until the receiver’s LED lights up.
• 3^rd step: Next, press one of the buttons on your new remote control. Hold it until the receiver’s LED turns off, then release the button.
• 4^th step: Finally, wait 10 seconds.
• 5^th step: Your new remote control AVIDSEN 104257 is programmed and ready for use.

FAQ for the AVIDSEN 104257 Remote Control

Why buy the AVIDSEN 104257 remote control from Alloremotecontrol?

• First, free shipping for the purchase of 2 remote controls or more
• Then, your order will be shipped the same day
• Next, test batteries are free
• A 1-year warranty is offered (with a possible extension of an additional year – see T&Cs)
• The manual is available for you (in PDF and video)
• Our phone or email support is available for you 5 days a week

Where to find other AVIDSEN products?

Discover all the models of AVIDSEN remote controls. Do you have an AVIDSEN remote control of a different reference and are looking for the compatible model? Contact us for free assistance.